400V on IR Lamp News

560mm 400v 1500w Halogen Quartz Lamp

Mon, 27 Jul 2026 15:02:42 +0800

Let’s talk about the 560mm Halogen Quartz Lamp

If you need heat—and you need it now—this is the tool for the job. We built these lamps for high-intensity infrared heating. The goal was simple: create something that hits hard and fast, but spreads that 1500W of power across a 560mm stretch so you don’t end up warping your workpieces with accidental hot spots. The nitty-gritty on the power Running at 400V is a deliberate move. It lets us push a ton of power through the tungsten filament without the current getting out of hand. If you’re running a standard industrial three-phase system, this will feel right at home. The best part? The ramp-up is nearly instant. We use a quartz envelope because it can handle the brutal heat of the halogen cycle. Basically, the gas pushes the tungsten back onto the filament as it operates. It stops the wire from thinning out, which means the lamp doesn’t just burn out the moment things get intense. Why quartz and halogen? We went with quartz glass because it doesn’t melt under pressure and lets short-wave IR radiation pass right through. By filling it with halogen gas, we can crank up the filament temperature. This shifts the energy. Instead of just giving you a bright light, it pours that energy into the infrared spectrum. That’s where the real heating happens. One quick tip: check your sockets. If you’re swapping these into an old rig, make sure everything is rated for 400V. You really don’t want to deal with arcing at the terminals. Where this actually lives (and how not to kill it) You’ll usually see these humming along in PET blowing machines, plastic welding setups, or curing lines. That 560mm size is great for getting a consistent heat zone over larger preforms. But here’s the thing. 1500W in a small tube is an incredible amount of heat. If your reflectors are dusty or slightly crooked, you’re asking for trouble. You risk overheating the ends of the lamp, and that’s a fast track to failure. Make sure your cooling fans are actually doing their job and your airflow is dialed in. Without a way for the heat to escape, the “heat soak” will eat your lamp’s lifespan alive.

598mm 400v 2500w shortwave halogen heating lamp

Tue, 21 Jul 2026 00:33:37 +0800

Let’s Talk About the 598mm 2500W Shortwave Halogen Lamp

When you need to move a lot of heat, fast, this is the tool for the job. We built these lamps to handle some seriously intense thermal loads. Think of it this way: you’ve got a 598mm tube pushing 2500W at 400V. That’s a massive amount of power focused right on the surface of whatever you’re heating. Because it uses shortwave infrared (SWIR), the heat doesn’t mess around with the air—it punches straight through plastics and coatings. It’s why these are the go-to for industrial lines where every second counts. The Power Side of Things We go with 400V for a reason. It lets us hit that 2500W mark without blowing out your current draw. Plus, with a tube this long, the higher voltage keeps the temperature steady from one end to the other. You get a concentrated blast of heat. No long wait times. No sluggish ramp-up. One quick heads-up:watch your wiring.2500W creates a lot of heat right at the terminals. Make sure your sockets can actually handle the voltage, or you’re going to end up with burnt-out connection points. Trust me, you don’t want that. What’s Under the Hood? The heating element lives inside high-purity quartz glass. To keep things running longer, we fill the envelope with halogen gas. This stops the tungsten filament from evaporating, which means your glass stays clear and the lamp doesn’t burn out prematurely. The best part? The heat travels in a straight line. It hits your material instantly. That’s exactly why you’ll see these in PET blowing or shrink-wrapping setups. It’s just immediate. Fitting Them In (And What to Watch Out For) These are designed as drop-in replacements for most standard 600mm industrial heaters. They don’t take up much space, but they pack a huge punch. But here’s the catch: they gethot. I mean, really hot. At 2500W, that quartz tube is reaching extreme temperatures. If your reflectors get dirty or a cooling fan decides to quit, that heat is going to soak right back into your machine frame. Make sure your cooling system is up to the task, otherwise, you might find your lamp housing starting to warp.