Machines on IR Lamp News

Replacement lamps for all blowing machines

Sun, 19 Jul 2026 00:10:08 +0800

Dealing with Heat Issues in KHS Blowing Machines

Ever pull a batch of PET bottles off the line only to find they’re distorted or the walls are thin in some spots and thick in others? It’s a headache. Usually, it comes down to the heating. Most of the time, it happens because the OEM lamps have just worn out, or someone swapped them for replacements that don’t actually put out heat the way the original ones did. The trick isn’t just cranking up the wattage. It’s about getting a steady, even heat field across the whole preform.

3000w short wave halogen heating lamp for blowing machines

Tue, 30 Jun 2026 11:31:12 +0800

The 3000W Short Wave Halogen Heating Lamp for Blowing Machines

We built this 3000W short wave halogen heating lamp for one reason: the blowing machine floor. It’s all about getting intense heat exactly where you need it—right onto the parison or preform—without wasting energy. This isn’t some general-purpose heater. It’s a focused tool, built to match the exact thermal needs of PET and other blow molding work.

500mm 220v 1000w halogen lamp infrared heating lamp for pet machines car infrared heat lamps

Wed, 27 May 2026 22:08:33 +0800

Power and Size, Sorted

So, we built this 500mm infrared heater for industrial machines that need heat in a tight spot. The 220V, 1000W rating isn’t by accident. It hits that sweet spot: enough punch to warm big surfaces fast, but still easy on your standard control panels and wiring. And that 500mm length? It spreads the heat just right, so you don’t get hot spots on curved parts—think PET blow molds or car body panels.

ir halogen heat lamp for pet blowing machines

Sat, 09 May 2026 11:00:13 +0800

We built these IR halogen heat lamps for one reason: to keep up with the pace of PET blowing machines. These aren’t just off-the-shelf heaters. They were designed for intense, focused heat, where every second counts and temperature control can make or break the job. Here’s the power and fit, in plain terms. Most run at 2500W and 400V, with a 300mm active length. That combo packs a lot of heat into a small space. And running at 400V means less current draw than a 230V unit. Less strain on the wiring, less energy lost along the line, and a cleaner install. The 300mm length lines up with the neck heater zones on most blow molds, so you can swap it in and get back to work. Now, what’s happening under the hood. The halogen cycle keeps the quartz envelope stable, even when the filament runs hot. That translates to steady output, day after day. The shortwave IR hits the PET preform fast, with almost no wasted energy heating the surrounding platen. And the R7s double-ended connector does its job: it holds the lamp securely, handles the high current, and makes replacements quick and simple when it’s time to change one out. On the line, this is what you feel. You need heat, and you need it to stay put. This setup responds quickly and holds temperature steady, so preforms heat evenly. The trade-off? It’s all about heat density. That means your machine’s cooling and airflow need to be set up right, so the lamp and nearby parts stay within safe operating limits.

Heating Equipment 630mm 800w halogen bulb for stretch blow moulding machines

Wed, 22 Apr 2026 06:52:18 +0800

630mm 800W Halogen Heating Lamp for Stretch Blow Molding Machines

We build this 630mm, 800W halogen heating lamp specifically for the heat zones of stretch blow molding machines. Its job is to bring PET preforms to the exact temperature window needed for uniform stretching and wall distribution. In practice, that means stable output, fast recovery after door openings, and a footprint that matches the machine’s existing lamp cavity.

Power, Dimensions, and Electrical Specs

The 800W rating is not arbitrary. It is sized to deliver the heat flux required to raise preform surface temperature quickly, without oversizing the heater and wasting energy. The 630mm overall length gives you coverage across the full heating section, while keeping the lamp compact enough to fit standard reflector assemblies and service openings. This lamp is typically specified for high-voltage operation, commonly 400V, because stepping the voltage up allows the same power to be delivered with lower current. Lower current means smaller wiring, simpler insulation requirements, and less heat buildup at the terminals. It also reduces voltage drop over distance, which helps maintain consistent temperature across the heating zone. The trade-off is real: higher voltage demands stricter insulation integrity and proper safety clearances during installation and maintenance. You must wire it up to the rated voltage and polarity, and keep terminal connections clean and tight.